Driver Motor Dc Bldc Brushless 1.5a 15w 5v-12v Itytarg

IMPORTANT information you need to know before purchasing the item:

1. This mini brushless DC motor controller adopts high single chip integration, the drive motor without hall sensor, power supply for DC voltage regulator can not connect to alternating current (AC), enough power supply current, electric current within the scope of use, the kinds of brushless motor are numerous, it's also exquisite to match with the governor, we don't guarantee it can apply all the brushless motor, please ensure that the wiring is correct after the strong again electrify tries machine (In case of that the first electric commissioning you don't understand motor, built righteousness as the input voltage with 5.5-6V, after commissioning OK again according to the motor working condition and need to improve the voltage).

2. This mini three-phase brushless speed controller, the input power supply has A reverse connect protection, reverse would not burn, internal integrated over-current protection circuit chip set limit current detecting circuit, the normal work in 1.5 A peak 2 A continuous current, please contact with the working voltage, current, power of motor coordination, A far cry from what parameters are not suitable for use, such as force, will be out of some bad phenomenon have burn out the risk of main chip, the motor line lacks locked-rotor protect the motherboard and the LED light hint, but not for long time, do not have A three phase motor line contact undesirable phenomenon (brushless motor without hall to normal will start at the beginning of the start of the chip internal force issued A set of starting current, to achieve A certain moment of normal start would increase rapidly turning up the motor startup current, such as poor contact for motor can start sending wrong signals, if it is in the input voltage is higher when the impact is bigger, the most easy to burn out driving chip, therefore cause burn out the chip to be outside the scope of the warranty)

3. The brushless drive board on the market on the hard disk brushless motor to note the following points: (1) when the drive motor on market generally have three lines and lines of four points and three lines of three line motor directly connected to the drive plate W V U go, don't have to distinguish between order to pick up, but it must require wiring is firm, more than four line motor is a common thread COM, must find the public line (the public line is a collection of three lines generally coarser) don't need to pick up (public line must points out, if there is no points out, the public line hybrid junction in the three phase line motor is started up, the general is shaking a few stops, time is long and the possibility of damage to the motherboard driver must pay attention to!!! ) each of the other three lines connect the motherboard W V U (2) 7200 RPM hard drive motor power supply are not more than 12 V, between 5 to 12 V power for the first time in the case of don't know about motor built righteousness with 5.5-6 V battery of commissioning, normal operation and then increase the voltage according to actual condition, the hard drive motor general speed fast, small internal resistance coupled with most of them are used to build a righteous in the 5-9V voltage a better work, 12 V electricity can also work, we actually tested because the motor is used and the speed is fast easy fever has certain resistance motor, the risk of improper operation also has easy to burn drive. 7200 turn above motor resistance more tracey righteousness input voltage 5-7 v don't answer the pure dc 12 v (3) the power supply voltage, it is best to provide sufficient the current of 1.5 A above, the power quality is bad Current shortage will be the motor start or start is difficult, try this kind of mood can change good power supply

4. The brushless drive is mainly used in power no more than 15 w three-phase brushless motor, cannot be used to drive a motor, the factory packaging each product loading test, guarantee one hundred percent OK again shipment, due to the improper use of damaged act please detour, products we provide technical support on use, small problems can communicate to solve.

Specifications:

Working Voltage: DC 5V-12V (MAX. 15V)

Working Current: 1.5A (MAX. 2A)

Maximum Rated Power: 15W

Static Current: 0.005A (Stand by)

PWM Duty Cycle: 10000 RPM Board

Size: 30x25mm/1.18x0.98"