St-link Stlink V2 Swim Emulator Download Manager Stm8 Stm32

Descripción:

STMicroelectronics ST-LINK/V2 es un depurador y programador en circuito para la gama STM8 y STM32 de microcontroladores. El ST-LINK/V2 viene con un cable USB A a mini B que se conecta directamente al PC y proporciona alimentación al módulo. Este dispositivo se comunica con las MCU STM8 y STM32 a través de una placa de aplicación. Esto se realiza a través de las interfaces SWIM (módulo de interfaz de un solo cable) y JTAG/SWD (depuración de cable serie).

Alimentación de 5 V a través de USB Función DFU (Actualización directa del firmware) Indicador LED cuando está conectado al PC Temperatura de funcionamiento: 0 a +50 °C.

-ST-LINK / V2 está diseñado para la simulación de MCU de la serie STM8 y la serie STM32 y las herramientas de desarrollo de descarga en línea.
La serie STM32 se conecta a ST-LINK/V2 a través de la interfaz JTAG / SWD
La serie STM8 se conecta a ST-LINK/V2 a través de la interfaz SWIM
-ST-LINK / V2 conecta la PC a través de USB 2.0 de alta velocidad
-Apoyo a todos con la interfaz SWIM STM8 series MCU
-Soporte Kernel M0, M1, M2, M3, M4 con interfaz JTAG / SWD STM32 MCU serie

Features
· 5 V power supplied by a USB connector
· USB 2.0 full-speed-compatible interface
· USB standard A to Mini- B cable
· SWIM specific features
– 1.65 V to 5.5 V application voltage
supported on SWIM interface
– SWIM low-speed and high-speed modes
supported
– SWIM programming speed rate:
9.7 Kbytes/s in low speed and
12.8 Kbytes/s in high speed
– SWIM cable for connection to the
application via an ERNI standard
vertical connector (ref: 284697 or 214017)
or horizontal connector (ref: 214012)
– SWIM cable for connection to the
application via a pin header or a 2.54 mm
pitch connector
· JTAG/serial wire debugging (SWD) specific
features:
– 1.65 V to 3.6 V application voltage
supported on the JTAG/SWD interface and
5 V tolerant inputs
– JTAG cable for connection to a standard
JTAG 20-pin pitch 2.54 mm connector
– JTAG supported
– SWD and serial wire viewer (SWV)
communication supported
· Direct firmware update feature supported
(DFU)
· Status LED which blinks during communication
with the PC
· Operating temperature 0 to 50 °C
· 1000 Vrms high isolation voltage
(ST-LINK/V2-ISOL only)

The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32
microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire
debugging (SWD) interfaces are used to communicate with any STM8 or STM32
microcontroller located on an application board.

In addition to provide the same functionalities as the ST-LINK/V2, the ST-LINK/V2-ISOL
features digital isolation between the PC and the target application board. It also withstands
voltages of up to 1000 Vrms.

STM8 applications use the USB full-speed interface to communicate with the ST Visual
Develop (STVD) or ST Visual Program (STVP) software.
STM32 applications use the USB full-speed interface to communicate with Atollic®, IAR™,
Keil® or TASKING integrated development environments.