Dws-mh01 Sensor Multiple Caudalimetro + Sonda Tds + Ntc Temperatura Itytarg

12434

Nuevo producto

Cod: HJG-R037

Modelo: MH01

Caudal: 18L/H a 600L/H

Más detalles

1 Elemento

Advertencia: ¡Últimos artículos en stock!

compartir

$ 30.000,00 IVA Inc.

Más

Nombre del producto: medidor de sensor de Flujo de Agua de turbina de plástico para líquido de agua, medición de TDS.

N. ° de artículo: DWS-MH-01

Material: plástico blanco

Especificación:

Función: Sensor, control de caudal

Tamaño de la rosca: enlace rápido OD6.5mm para tubería ID6MM

Tubo de conexión: 6mm

Color: blanco

Caudal: 18 ~ 600l/hora

Flujo de pulso: F(Hz)=(24xQ) L/min +/- 2%

Corriente máxima de funcionamiento: 15mA (DC5 V)

Tensión mínima de funcionamiento: 4,5 V CC

Voltaje de funcionamiento: DC 5V ~ 18V

Capacidad de carga: = 10 mA (DC 5 V)

Presión: 0,1 ~ 0.8mPa

Temperatura de funcionamiento:

-25 grados centígrados a + 60 grados centígrados

Precisión: +- 2%

Cable wire :

red : +  ;  5V

Yellow : NPN signal output

Black :  - GND

Green:  NTC temperature sensor 50K.

Blue & Red :  TDS ( total dissolved solide)  water quality teser sensor.

El término TDS describe la cantidad total de sólidos disueltos en el agua. ... Cuanto mayor sea la cantidad de sales disueltas en el agua, mayor será el valor de la conductividad eléctrica. La mayoría de los sólidos que permanecen en el agua tras una filtración de arena, son iones disueltos.

More info

Water flow sensor 2 points PE tube high precision water flow sensor coffee machine flow meter 

 

Features:

1.This product is light and handy, small in size, plug and play, and easy to install.

2.Stainless steel shaft is inlaid inside the impeller.

3.The sealing ring adopts the structure subjected to upper and lower stresses and never leaks.

4.The Hall element is imported and isolated from water to prevent water ingress and never age.

5.All raw materials are in compliance with ROHS testing standards

Product introduction:

The water flow sensor is mainly composed of a plastic valve body, a water flow rotor assembly and a Hall sensor.

It is installed on the water inlet of various types of coffee machines, water dispensers, and electrolyzers. It is used to detect the water flow rate. When water passes through the water flow rotor assembly, the magnetic rotor rotates and the speed changes with the flow rate. The signal is fed back to the controller, and the controller determines the size of the water flow and regulates it.

 

 

Notes for use:

  • Strict impact and erosion by chemicals are strictly prohibited.
  • Do not throw or bump.
  • Install the inlet and outlet water according to the arrow on the product.
  • The temperature of the medium should not exceed 120 degrees .

Second, the output waveform:  square wave 

O1CN01SqW8M91z3PY4qfCFk_!!106586658.png

Third, the lead-out method:

 

 

   Red IN to positive 

   Yellow OUT signal output line

   Black GND connected to negative

 

 

Fourth, technical parameters

1 Starting water flow: <0.2L ∕ min
2 Starting water pressure: <0.1Mpa (Mpa)
3 Working water flow range: 0.2-8L ∕ min
4 When cleaning the residual water on the impeller with air, pay attention that the output signal cannot be higher than 150HZ, and the idle time should be within 30 seconds.
5 Maximum water pressure; 0.8Mpa (Mpa)
6 Working voltage range: 3.5-12VDC (DC voltage) DC voltage
7 Working current: 0.5-1.5mA (milliamps)
8 Working environment temperature: 1-100 ° C (Celsius)
9 Applicable ambient temperature: –40-100 ° C (degrees Celsius)
10 Output characteristics: [38 * Q] Q is the flow rate L / minHz (Hz) error ± 3%
11 Life: 10 6 H (hours) 5VDC1mA  
12 Electrical strength:> 600VAC (AC voltage) duration 5S leakage current 3mA
13 Insulation resistance:> 100mΩ (Megohm) Insulation resistance between connector and housing or valve body

13 productos más en la misma categoría: